FOCUSRITE PRO REDNET-R1 REDNET - Control surface for Red interfaces

The RedNet family of interfaces has been designed to meet the needs of a wide range of audio applications-from live sound to multi-cabin recording studios, houses of worship, distributed audio installations, post-production environments, and everything in between. Fundamentally, RedNet is a highly scalable audio distribution system that offers near-zero latency and can be used to expand the number of inputs and outputs of digital audio systems and/or serve as a bridge between Pro Tools|HD, MADI protocol, and the Dante audio network. Featuring Focusrite's most advanced AD/DA conversion to date, an ultra-stable JetPLL clock, and high-end multilayer PCBs, RedNet is no exception to Focusrite's philosophy: Sound is everything. Designed and built with extreme attention to detail, RedNet interfaces are a step above the competition, delivering transparency and some of the best sound quality to date - combined with the revolutionary capabilities of networked audio systems.

**Swiss Army Knife.**

The RedNet R1 can be configured to control groups of outputs from the multitude of sources and destinations available on Red interfaces. From Pro Tools ™ | HD and other DAWs, analog inputs and outputs, ADAT and S/PDIF connections, and from full Dante® audio ecosystems, audio can be switched and "summed" to multiple platforms simultaneously and interchangeably. Top panel controls are for level, reference level preset selection, Dim, Mute, and a variety of Solo modes.An A/B switch toggles between monitor presets and up to four presets for quick switching for submix checking.

**Hello, control tower...**

RedNet R1 also includes a Dante-compatible talkback, an internal mic preamp for connecting an external mic (talkback), a built-in microphone, and a headphone output, for monitoring audio inputs and outputs and interacting with performers and other network users. Up to four talkback destination groups are available - when used with a Red interface (when used with other Dante devices, only one talkback group is available).

**Flexibility and power.**

Two LCD displays show highly accurate level measurement of outputs, sources, and headphone output and provide visual cues for menu navigation. RedNet Control software is used to quickly set up both simple and complex monitoring and routing configurations. In addition, a 6.35mm jack accepts a footswitch for talkback management, LFE Mute and more.The RedNet R1 can be powered via Ethernet to reduce cabling complexity (using the PoE standard), or by the supplied power supply.

- Display: 2 LCD screens

- Category: audio network card

- Inputs: Dante, XLR

- Outputs: Headphone/Line, Dante

- Built-in mic: Yes

- Phantom power: Yes

- Sampling rate: 96 kHz

- No. of channels: 2

- No. of mic inputs: 1

- Additional Specs: INTERNAL TALKBACK

- Gain Range: 0dB to 55dB

- Type: electrically balanced (input impedance = 3kΩ)

- Max Input Level: +10dBu ± 0.5dB

EXTERNAL CALKBACK

- Gain range: 0dB to 55dB

- Max input level: +10dBu ± 0.5dB

- Frequency response: 20Hz - 20kHz ± 2dB

- THD + N: <-98dB (0.0012%) @ -1dBFS

- Equivalent input noise: <-128dBu

- Signal to noise ratio: -111dB 'A'-Weighted (typical), min gain

- Common mode rejection: 50/60Hz CMRR: <-77dB

- Type : Electrically balanced (input impedance = 3kΩ)

HEADPHONE OUTPUT

- 0DBFS reference level: +11dBm

- Frequency response: 20Hz to 20kHz ±0.5dB

- THD + N: -100dB (0.001%) @ -1dBFS, Rs = 150R

- Dynamic range: 108dB, 20Hz - 20kHz

- Noise in presence of Signal: >-97 dBu 'A-Weighted'

- Output impedance: 5Ω

- Headphone Impedance: 32Ω - 600Ω

MICROPHONE & LINE DIALOGUE

- Mic In to Headphone Out: <-84dB; 20Hz - 20kHz (other channels @ 0dBFS)

HEADPHONE DIAPHONY

- Left to right: <-85dB; 20Hz - 20kHz (other channels @ 0dBFS)

- Right to left : <-85dB; 20Hz - 20kHz (other channels @ 0dBFS)

DIGITAL

- Supported frequencies: 44.1/48/88.2/96kHz (-4%/-0.1%/+0.1%/+4.167%) in 24 bit

- Clock sources: Internal or External from Dante network.